Don’t Do These Things with Your Brand New Daiwa Fishing Rod

So you’ve got a new Daiwa fishing rod – congratulations, these are widely lauded as some of the best in the sport.

But now you want to protect your investment, because doing any of the following is likely to incur damage.

Don’t do the following.

High Stick

High sticking refers to pulling the rod back so that the tip would be upward at the sky, but with the rod under a heavy load, which bends the tip back down towards the water. Doing so is likely to incur breakage. You may be able to fix a broken tip but if it breaks closer to the rod butt you’ll be out of luck.

Leave It on the Deck

Never leave your rod laying on the deck, or on the dock, or anywhere on the ground for that matter. It’ll be a matter of time before someone steps on it, and then you’re likely looking at a broken rod.

Travel Without a Rod Sleeve/Sock/Case

If you’re just going down the street to a fishing hole that’s one thing, but don’t take your rod on any long trips without cushioning it with some sort of sleeve, sock or case. The reason why should be self-evident.

Go Anywhere Without a Tip Repair Kit

A broken tip can happen anywhere; in port or out on the open water, and if you don’t have a tip repair kit with you (plus a lighter and some adhesive) your rod will be crippled until you get back home.

Leave It Outside

Extreme temperature shifts are not good for your rod but there are two things that are worse: high moisture and direct sunlight exposure. The former can rust the rod guides (if they are steel) and the latter will break down the EVA or cork in the grip, and it might even break down the epoxy matrix that binds the carbon fibers of the rod. Plus, sunlight breaks down fishing line, so keep the rods inside.

Leave It in the Shed/Garage

The same notes apply here. Storing your Daiwa fishing rods where there is no climate control is like leaving them outside. Don’t do it.

Swing the Fish

Never swing the fish over the rail, even if it’s tiny. For one thing, you run a massive risk of losing the fish at that critical moment, and even if you don’t care about that, the action will put immense stress on the rod, vastly improving your odds of breaking it.

Touch the Gunwale

Rods are designed to bend parabolically in such a fashion that the load is distributed evenly. Letting your rod touch the gunwale or rail as your fighting might give your arms a rest, but it creates a pressure point at which the rod is likely to snap.

Reel the Rig into the Eyelet

Never reel your rig all the way in so that it hits the last eyelet on the rod, that is likely to chip the insert, which will therefore fray your line, resulting in higher risk of breakoff.

Forget to Use Your Hook Keeper

Your hook keeper is there for a reason – use it. Don’t just hook your rig onto an eyelet, as that will likely chip or otherwise damage the eyelet insert, which can damage your line.

Time for a New Daiwa Fishing Rod?

If, for any reason, you’re in the market for a new Daiwa fishing rod (we won’t ask questions) visit No Bad Days Kayaks. They carry a wide range of baits and tackle, including rods and reels. Visit their website and if you need help or want a personalized recommendation, get in touch with them.

Leave a Reply

Your email address will not be published. Required fields are marked *

Busniess

Understanding the Quality and Value of a Lab-Grown Diamond Tennis Bracelet

A lab-grown diamond tennis bracelet offers lasting elegance, everyday comfort, and exceptional craftsmanship in a single piece of jewelry. While its timeless appearance captures immediate attention, its true value comes from careful construction, quality materials, and thoughtful design. Understanding these details helps you appreciate what makes a bracelet beautiful, durable, and enjoyable to wear for […]

Read More
Busniess

Roller-Delayed PCCs: 9mm vs. 10mm

That one extra millimeter in caliber makes a serious difference in cartridge performance between the 9mm Luger and 10mm Auto. If you’re tossed up between a roller-delayed PCC chambered in one of these, here’s what you should know about them. Where the 9mm Excels If you’re considering a roller-delayed PCC chambered in 9mm, here are […]

Read More
Busniess

The Checklist Facilities Managers Use Before Ordering PTAC Units

Facilities managers who’ve been through a commercial HVAC procurement cycle before don’t start with a brand name. They start with a list. Ordering PTAC units for a multi-room property involves more variables than most buyers expect, and the teams that get it right aren’t necessarily the ones with the biggest budget. They’re the ones who […]

Read More