Want to Re-Fit a PING G425? Consider One of These

While PING makes some of the best driver heads in golf, it’s not known for golf shafts. When you buy a “PING club,” you’re likely getting it with another manufacturer’s golf shaft fitted to it.

Which is fine. Specialization drives economic excellence, after all. But that’s little help to you if you’re looking to re-outfit a PING G425 and don’t know what shaft to choose.

In lieu of an actual PING golf driver shaft, we suggest one of the following.

1.Mitsubishi TENSEI AV RAW Orange
The Mitsubishi TENSEI AV RAW Orange produces mid-launch and low-spin profiles to maximize distance and control shot dispersion.

The RAW Orange is a series of counterbalanced shafts that have their balance points shifted higher on the shaft towards the butt section.

This higher balance point empowers players to tinker with the performance of the outfit by adjusting the weight of the driver’s head or by altering the length of the shaft since most of the mass is situated higher on the shaft.

These shafts are also made with ultra-lightweight carbon fiber and contain low resin concentrations; they’re also reinforced through aluminum vapor deposition which stabilizes the shaft. With a thinner and tighter weave, these shafts resist ovaling under force.

These shafts are tops if you need a PING golf driver shaft that produces mid-launch profiles and consistently low launch, for longer drives and tighter control over shot dispersion.

2.Aldila ROGUE White
Like the Mitsubishi TENSEI AV RAW Orange series, the Aldila ROGUE White also features a high balance point that is the product of thicker fiber shaft walls near the butt of the shaft. This results in lighter shafts that can produce higher club head speeds.

Aldila ROGUE White golf shafts are also made with DIALEAD Pitch Fiber that is extremely strong, resists ovaling and shaft deformation, and has excellent energy transfer properties.

Stronger than shafts made using traditional carbon fiber, and with similar properties (high balance point and strong fibers that resist deformation under stress), the Aldila ROGUE White will also produce consistent mid-launch and low profiles that will help golfers extend their ranges while controlling shot dispersion.

Looking for Advice or Recommendations for PING Golf Driver Shafts? Visit Dallas Golf Company
We make these recommendations for PING golf driver shafts because PING itself actually recommends them for its G425 drivers.

But not every player has the same athletic abilities, nor the same needs in clubs and golf shafts. The best way to know for sure that you’re playing with gear that complements your skill set is to work with a professional golf club fitter.

If you’re in Texas, visit Dallas Golf Company and work with them for professional golf club fitting services to find a club and golf shaft combination that works best for you.

If you’re not in their area, visit their website, DallasGolf.com, which carries a huge range of PING clubs and golf driver shafts – if you have any questions, you can always consult them at 800-955-9550.

Leave a Reply

Your email address will not be published. Required fields are marked *

Busniess

What Makes .408 and .375 CheyTac Two of the Best ELR Cartridges Out There?

You can shoot a rifle chambered in .50 BMG, .338 Lapua, or .300 Norma Magnum at extreme ranges, and it will perform well as long as your rifle is sighted-in properly and you train with it. Both of these cartridges have a vetted history of performance as extreme long-range rifle cartridges, with the former two […]

Read More
Busniess

Sizing a Laboratory Air Dryer for a Few SCFM

Benchtop setups rarely draw much compressed air. Buyers still end up with a laboratory air dryer rated for a machine shop, because the sizing numbers on most spec sheets don’t mean what they look like they mean. Inlet, purge, and outlet flow are three different figures. Sizing to the wrong one either wastes air and […]

Read More
Busniess

Types of End Mills Used in Machining

There is a surprisingly wide variety of different types of end mills used in machining, some of which are used for rough stock removal and cutting a workpiece to shape, and others which are used to impart a desired finish to it, with a whole lot in between. This short post will take a quick […]

Read More